Glenair High-Speed Micro-D Connectors and Cables

Glenair High-Speed Micro-D Connectors and Cables

High-Speed Micro-D uses an impedance optimized open pin field for high-density signal routing flexibility. 1 Amp pre-wired cable and PCB solutions deliver up to 15 Gbps performance per differential pair. Auxiliary EMC ground springs on plugs ensure data integrity and low attenuation performance.

For USB 3.010GbECamera LinkPCIe 3.0

Series GHSM

The High-Speed Micro-D achieves its high-speed signal integrity and high data rate performance through innovative modifications to the standard Micro connector insert, principally in the use of an ultra-low dielectric insulation material, but in addition, with the use of Nano TwistPin contacts, exactingly spaced and isolated to eliminate cross-talk and maintain impedance levels through the connector mating interface.

Available in both prewired factory cordsets — with hybrid shielded twisted pair (STP) and standard hookup wire cabling — as well as PCB configurations, the High-Speed Micro-D utilizes #28 gauge wire and is rated at 1 amp per contact (instead of the usual 3 amp rating found in standard Micro connectors).

  • Pre-wired factory pigtails, cordsets, and PCB connectors
  • Unique contact isolation and spacing for optimal high-speed performance up to 15 Gbps
  • Supports maximum #28 AWG wire
  • Low-k dielectric insulator combined with optimized contact size and spacing
  • Precision-machined shells with gold or nickel plating
  • 1 Amp TwistPin contacts for optimal performance in harsh vibration, shock, and high-temperature environments

Like other next-generation rectangulars from Glenair, the High-Speed Micro-D incorporates an auxiliary EMI ground spring on the plug, further enhancing the signal integrity of this ultra-small form-factor connector. In fact, the High-Speed Micro-D's size is perhaps its most important advantage as it is now arguably the smallest and lightest aerospace-grade high-speed interconnect.

The downselect process begins with the identification of the target high-speed protocol. Each insert arrangement in the series is purpose-designed to meet the particular requirements of today's most popular high-speed datalink protocols. Prewired pigtail assemblies utilize shielded twisted pair cabling for the high-speed data pairs, and #28 gauge hookup wire for power and low-speed signal requirements. Ground wire terminations are also indicated for each insert arrangement. Consult Glenair Design & Installation of High-Speed Micro-D PCB Connectors Application Note for board layout and termination requirements.

Reference

Related Glenair Content

Series GHSM – Glenair High-Speed Micro-D Test Report

High-Speed Micro-D Connectors and Cables

Glenair High-Speed Micro-D Connectors and Cables

For USB 3.010GbECamera LinkPCIe 3.0

Series GHSM

  • eBook
  • PDF (Single pages, print friendly)
GHSM Prewired Pin and Socket Cable Connectors: Pigtails and Double-Ended Assemblies

GHSM Prewired Pin and Socket Cable Connectors
Pigtails and Double-Ended Assemblies

GHSM cable connectors are pre-wired for use with specific high-speed datalink protocols. Each assembly is available as a single-ended wire pigtail or back-to-back jumper, pre-wired with STP cable for dedicated differential data pairs (plus ground wire). Remaining contacts are terminated with standard hook-up wire for low-speed signal or power. Choose the insert arrangement, per the table, that matches the target high-speed protocol.

GHSRPM Prewired Pin and Socket Rear Panel-Mount Connectors: Single-Ended Pigtails

GHSRPM Prewired Pin and Socket Rear Panel-Mount Connectors
Single-Ended Pigtails

GHSM-BSS Straight Surface-Mount Pin and Socket PCB Connectors (Jackpost Hardware)

GHSM-BSS Straight Surface-Mount Pin and Socket PCB Connectors

  • Jackpost Hardware
GHSM-BSS Straight Surface-Mount Pin and Socket PCB Connectors (Jackscrew Hardware)

GHSM-BSS Straight Surface-Mount Pin and Socket PCB Connectors

  • Jackscrew Hardware
GHSM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket PCB Connectors (Jackpost Hardware)

GHSM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket PCB Connectors

  • Jackpost Hardware
GHSM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket PCB Connectors (Jackscrew Hardware)

GHSM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket PCB Connectors

  • Jackscrew Hardware
GHSRPM-BSS Straight Surface-Mount Pin and Socket Rear Panel-Mount Connectors (Jackpost Hardware)

GHSRPM-BSS Straight Surface-Mount Pin and Socket Rear Panel-Mount Connectors

  • Jackpost Hardware
GHSRPM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket Rear Panel-Mount Connectors (Jackpost Hardware)

GHSRPM-HBR Hybrid Right-Angle (Surface-Mount / Thru-Hole) Pin and Socket Rear Panel-Mount Connectors

  • Jackpost Hardware
GHSM-USP1 Sav-Con® Connector Saver

GHSM-USP1 Sav-Con® Connector Saver
2-Row, 9 thru 67 Position

Protect Sensitive Equipment with the GHSM-USP1 SAV-CON® Connector Saver

Prevent contact damage and extend the service life of cable assemblies. Protect High-Speed Micro-D connectors that are mated and unmated frequently during manufacturing, test, check-out phases, and environmental test programs. Sav-Con®s prevent costly repair or replacement by absorbing connect and disconnect abuse.

  • Sav-Con® Connector Savers
    The Smart Solution for Preventing Contact Damage and Extending the Service Life of Cable Assemblies and Mounted Receptacles
Dust Covers for High-Speed Micro-D Connectors, 500-148

500-148
Dust Covers for High-Speed Micro-D Connectors

Plug and Receptacle Dust Covers

Jackpost Kit, 179-045

179-045
Jackpost Kit

Jackpost Kit for Panel-Mount Connectors

O-Ring for Sealing of Panel Mount GHSRPM Connectors, 179-276

179-276
O-Ring for Sealing of Panel Mount GHSRPM Connectors

Replacement O-Ring for Panel Sealing of GHSRPM Connectors

100 Ohm Differential Twisted Pair Cable with Drain, #28 AWG, 963-057-28

963-057-28
100 Ohm Differential Twisted Pair Cable with Drain, #28 AWG